ACS355:ABB small‑size machinery‑specific drive series, designed for OEM machinery integration. 03:Three‑phase AC input unit. E:Unit with built‑in standard EMC electromagnetic filter. 12A5:Rated continuous output current 12.5 A. 4:Three‑phase supply voltage class 380~480 V,50/60 Hz. Matched for 5.5 kW three‑phase asynchronous motor. Frame size R3.
Three‑phase AC 380480 V, voltage tolerance +10%/‑10%, input frequency 47.563 Hz. Built‑in Class C2 EMC filter complying with industrial EMC standards. Rated operating efficiency meets IE2 energy‑efficiency class.
Three‑phase output voltage 0480 V, adjustable output frequency range 0600 Hz. Rated continuous output current 12.5 A; 150 % rated‑current overload for 60 seconds within every 10‑minute cycle; withstands 180 % current for 2 seconds at instant start‑up. Matched for 5.5 kW three‑phase asynchronous induction motor. Supports sensorless vector control for permanent‑magnet synchronous motors.
Dual control modes: scalar V/F control and sensorless vector control. Vector control delivers high low‑speed torque for heavy‑duty start‑up conditions. Factory‑default switching frequency 4 kHz; four optional settings:4 kHz,8 kHz,12 kHz,16 kHz. Switching frequency automatically decreases under high‑temperature conditions for noise reduction and overheat protection.
Built‑in Class C2 EMC electromagnetic filter. Reserved mounting interface for external brake chopper; external braking resistor can be connected for dynamic braking. On‑board RS485 Modbus RTU communication interface. Supports external control panel with integrated USB debugging port. Circuit boards with three‑proof conformal coating. Vertical independent isolated air‑duct cooling structure.
Protection class IP20. Overall dimensions:W169 mm × D195 mm × H236 mm. Net weight 3.8 kg. Vertical wall‑mount installation inside control cabinet. Full‑load output within‑10℃ ~ +40℃ ambient temperature; proportional derating required for 40℃ ~50℃. Full‑rated output up to 1000 m altitude; 1 % power derating per additional 100 m above 1000 m. Operating relative humidity 5%‑95%, no condensation, no corrosive conductive dust. Certifications:CCC, CE, UL, RoHS; compliant with EN61800 low‑voltage drive standard.
6 digital input channels, passive inputs, PNP/NPN universal, internal 24 VDC power supply. Functions:equipment start‑stop, multi‑speed switching, fault reset, PID mode switch, external interlock signal input. 2 analog input channels, adaptive for 010 V voltage and 420 mA current signals, compatible with pressure, temperature and level transmitters. 1 analog output channel, supporting 010 V /420 mA output, transmitting motor running frequency, output current and speed data. 3 relay output channels, passive contacts 250 VAC/8 A, independently output running, fault and alarm signals. On‑board RS485 communication terminal for direct connection with PLC, HMI and host SCADA systems.
Sensorless vector control provides stable high low‑speed torque for heavy‑duty applications such as conveyors, agitators and extruders. Supports 7‑step multi‑speed operation via digital‑input gear switching. Linear / S‑curve acceleration‑deceleration selectable; ramp‑time range:0.1 s‑1800 s. 16 sets of one‑click application macros covering general operation, 3‑wire start‑stop, PID constant‑pressure control, multi‑speed, crane, wood‑working machinery and packaging‑equipment scenarios. Built‑in simple sequence programming for custom interlock logic, reducing requirements for small auxiliary PLCs. Automatic motor identification precisely matches motor parameters and improves control accuracy. Stores up to 50 historical fault records. Supports offline parameter copying via MFDT‑01 FlashDrop tool.
Built‑in PID closed‑loop regulation with sleep‑wake‑up energy‑saving logic:low‑load low‑frequency sleep; automatic wake‑up when process pressure falls below set threshold. Fire forced‑run mode:all fault protections are suppressed and fans run at full speed upon trigger. S‑curve soft‑ramp acceleration/deceleration to suppress water‑hammer impact. Built‑in anti‑surge and flow‑compensation algorithms.
Instant pulse blocking for output overcurrent, phase‑to‑phase short‑circuit and earth short‑circuit. Graded alarm and shutdown for DC‑bus overvoltage / undervoltage. Heatsink pre‑alarm and overtemperature shutdown protection. Electronic thermal overload simulates motor overheating protection. Supports external PTC thermistor for motor‑winding temperature monitoring. Input phase‑loss, voltage‑unbalance and output earth‑fault monitoring. Complete protection logic:power‑fail buffered stop and cooling‑fan‑fault detection.
ACS‑CP‑A Chinese graphic control panel, supports remote installation with extension cables. ACS‑CP‑D basic digital panel for fundamental parameter display and operation.
FPBA‑01 Profibus‑DP module, FENA‑01 Ethernet/IP module, FDCO‑01 DeviceNet module, FMBA‑01 Modbus communication adapter.
External brake chopper and power‑matched braking resistors for fast‑stop and inertia‑load applications.
Input line reactor, output dv/dt filter for long motor‑cable applications.
IP66 high‑protection outdoor enclosure kit, DIN‑rail mounting bracket, panel‑mount base.
MFDT‑01 FlashDrop parameter copier, Drive Composer PC debugging software.
Compact footprint, suitable for limited installation space inside small‑size OEM control cabinets. Multiple built‑in machinery‑oriented application macros greatly improve on‑site commissioning efficiency for machinery manufacturers. Dual scalar‑and‑vector control supports both variable‑torque loads (fans/pumps) and constant‑torque loads (processing machinery). Compatible with asynchronous and permanent‑magnet motors for permanent‑magnet‑motor retrofit projects. Standard built‑in EMC filter eliminates extra filtering devices and simplifies cabinet wiring. Rich field‑bus expansion options for interconnection with mainstream industrial PLC control systems. Reliable cooling structure; three‑proof coated circuit boards adapt to dusty and humid workshop environments. Wide grid‑voltage tolerance for unstable‑voltage sites such as factories and construction sites. Standardized accessories; control panels and debugging tools are interoperable across the full ABB drive portfolio.
Wood‑working machinery, textile equipment, packaging production lines, small extruders, cutting machines, agitators; HVAC: small cooling‑tower fans, fresh‑air/exhaust equipment, small circulating pumps; Building water supply: small constant‑pressure water‑supply pumps, sewage circulating transfer pumps; Food‑processing conveying equipment, drying fans, filling‑line drive units; Small process‑cooling chiller circulating pumps, dust‑removal fans, small laboratory constant‑temperature‑equipment drives.